Innokin iTaste MVP3.0 Pro 60W Express Kit 4500mAh
60W iTaste MVP3Pro is the newest highly powered vaporizer. Not only having perfect size and clean lines, the 4500mAh MOD also provides perfect flavors and unbelievable huge clouds working with iSub G Tank.
Produk ini tidak akan mengisi lagi. Kami telah menyiapkan banyak produk menakjubkan lainnya untuk Anda pilih di situs kami.
Anda boleh membeli bermacam produk untuk mendapatkan harga grosir
USD 49.99 USD 74.99
USD 49.99 USD 74.99
USD 51.99 USD 76.99
USD 36.99 USD 45.00
USD 59.99 USD 89.99
USD 34.99 USD 42.00
USD 44.99 USD 55.00
USD 70.00 USD 105.00
USD 79.00 USD 118.50
USD 22.60 USD 33.90
1. Innokin now requires Serial No. (below barcode) before providing replacements (due to counterfeits in market). We recommend you to keep the packing boxes after you get parcel, or take a picture of Serial Number before you discard it. Thank you!
2. Shipping restriction: Due to exclusive distributor of Innokin, we do not send Innokin products to customers in Australia, Iceland, Portugal, Ireland, Germany, Austria or Switzerland. You can check more exclusive distributors .
60W Innokin iTaste MVP3.0 Pro VV/VW Express Kit
60W Innokin iTaste MVP3.0 Pro VV/VW Express Kit is the newest highly powered vaporizer. With perfect size and clean lines, the iTaste MVP3.0 Pro features high compatibility 510 connector, can work with all standard 510 clearomizers & atomizers including the iClear 16, iClear 16B, iClear 16D, iClear 30, iClear 30B, iClear 30S and the iSub Tanks.
Parameters of MVP3.0 Pro MOD
Operating Voltage: 3.0V - 9.0V
Operating Wattage: 6.0W - 60W
Battery Capacity: 4500mAh
Operating Resistance: 0.2ohm - 0.5ohm
Charger Port: Micro USB
Parameters of iSub Tank Cartomizer
Recommended Wattage: 20W - 35W
It comes with
- 1 x 60W Innokin iTaste MVP3.0 Pro VV/VW MOD
- 1 x 510-eGo Adapter
- 1 x USB Cable
- 1 x MPV3.0 Pro Manual
- 1x Innokin Sticker
Simple packing. Customary packing from the factory, the packing is subject to change without notice.
1. 15 seconds cut-off
2. Flip OLED Screen Orientation
3. Low Voltage Warning
4. Short Circuit/ Atomizer Protection
5. Overheat Protection
6. Over-discharge Protection
7. Pass-through Function
8. Remembers Last Voltage or Wattage setting
9. Portable power source for electronic products
How To Use the MOD
1. Press "Power Button" three times to turn on the device.
2. The LED light on the top will blink to display the current battery level. Green indicates the battery is almost fully charged. The LED light will power off when it's fully charged. Yellow means around half power left, while Red means low power, you need to get the device charged.
3. When the power button is pressed, the OLED screen will display the attached atomizer resistance, voltage, wattage and remaining battery level.
4. Hold on both "+" and "-" buttons simultaneously, the screen will display: resistance of atomizer, battery voltage, puffs taken since the device was last turned off and the last set voltage or wattage.
5. Press both "+" and power button to enter variable wattage mode. Click "+" or "-" to adjust the wattage by 0.1 wattage.
6. Press both "-" and power button to enter variable voltage. Click "+" or "-" to adjust the voltage by 0.1 voltage.
How to Fill the Cartomizer
1. Carefully unscrew the metal section.
2. Add e-liquid against the inside wall of the tank.
3. Carefully and firmly tighten. Do not overfill.
4. Prepare coils by adding 2-3 drops e-juice to the center wicks. Wait 1 minute before vaping.
How to Replace Coils
1. Unscrew the top section of the metal cap.
2. Gently hold and pull the coil out.
3. Align the flat sides of a new coil.
4. Push and insert the new coil to tank.
5. Carefully and firmly tighten the metal cap.
- There is CE mark on the package.
- No e-juice included. You have to buy it here.
Replacement coils is available.
Pls check guarantee policy.
Share your thoughts with other customersTulis ulasan
Typical questions asked about products:
- Is the item durable?
- Is this item easy to use?
- What are the dimensions of this item?